Cisco 642-384 Questions, Most Popular Cisco 642-384 Dump Is What You Need To Take

Flydumps has timely updated the Cisco 642-384 exam questions.With all the new questions and answers, you will pass the Cisco 642-384 exam easily. If you want to get more Cisco 642-384 exam dumps, you can free download the new version VCE test engine from Flydumps.All Cisco 642-384 dumps are new updated and cover all aspect of the examination.

QUESTION 41
What can be used to troubleshoot complex network and VPN connectively issues?
A. NAT
B. CCP
C. IPsec
D. NAC
Correct Answer: B Section: (none) Explanation

Explanation/Reference:
QUESTION 42
Where might you go on the Cisco ASDM home page to review graph outputs?
A. Configuration
B. Routing
C. Monitoring
D. Home

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 43
Which three types of ACL would you use to secure traffic on the network? (Choose three)
A. VLAN
B. reflexive
C. packets
D. dynamic
E. IPS
F. firewalls

Correct Answer: ABD Section: (none) Explanation
Explanation/Reference:
QUESTION 44
Which two statements are correct about OSPF in a multiarea environment? (Choose two)
A. OSPF will be default summarize updates between area
B. OSPF requires the use of the area range configuration command only whennondefault summarization is required
C. OSPF ABR routers are needed only at the boundary of another OSPF area
D. OSPF uses wildcard masks in the network statements but subnet masks in the area range statements
E. OSPF requires that all areas have a least one ASBR

Correct Answer: CD Section: (none) Explanation
Explanation/Reference:
QUESTION 45
OSPF routes are being redistributed into EIGRP but they are not showing up in the routing table. What are two possible causes? (Choose two)
A. CEF has not been enabled
B. Synchronization has been turned off
C. Incorrect distribute lists have been configured
D. No default metric has been configured for EIGRP
E. Theip classless command is missing
F. There are mismatched autonomous system numbers

Correct Answer: CD Section: (none) Explanation
Explanation/Reference:
QUESTION 46
You are configuring a VLAN and the switch you are using requires that you do so within the VLAN databases. Which command allows you to enter the VLAN databases?
A. Switch#vlan database
B. Switch (config) # vlan database
C. Switch (config-if) # vlan database
D. Switch (vlan)# vlan database

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 47
Which three statements are correct about the IEEE 802.3af Power over Ethernet standard? (Choose three)
A. It defines a port that acts as a power source to be a PSE
B. It defies a powered device to be a PDE
C. It defies how a powered device is detected
D. It defies three methods of delivering Power over Ethernet to the discovered powered device
E. It describes five power classes to which a device may belong
F. It defines power class 0 as being reserved for future use

Correct Answer: ACE Section: (none) Explanation
Explanation/Reference:
QUESTION 48
What is the primary purpose of SMB Smart Designs?
A. assists in locating appropriate resources
B. provides validated commercial solutions
C. provides training on products, tools, and solutions
D. provides a direct support path for any partner issue
E. provides a step-by-step outline of implementation tasks required
Correct Answer: B Section: (none) Explanation

Explanation/Reference:
QUESTION 49
Which of these is the best definition of the Cisco Lifecycle Services approach?
A. It defines the minimum set of services required to successfully deploy and operate a set of Cisco technologies
B. It determines how best to price Cisco products
C. It provides partners with a useful way to leverage Cisco resources
D. It consists ofthese phase: plan, deploy, support, and troubleshoot

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 50
How are lightweight access points different than autonomous access points?
A. Lightweight access points are managed individually
B. Lightweight access points are B, G,N capable
C. Lightweight access points require external antennas
D. Lightweight access points require a WLAN controller

Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 51
Before installing Cisco ASDM, it is important to allow connectivity on the side interface of which device?
A. ISR
B. WLC
C. ASA
D. Cisco Security MARS

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 52
Which two are characteristics of HSSI cables? (Choose two)
A. HSSI cables use a female, 10-pin, SCSI-II-type connector
B. The HSSI connector and the HSSI cable are identical
C. HSSI cables use cable CAB-HSI 1 and cable CAB-HNUL
D. The HSSI connector and the HSSI cable are similar E. The CAB-HUNL is used to connect your router to an external DSU

Correct Answer: CD Section: (none) Explanation
Explanation/Reference:
QUESTION 53
Which statement best describes clustering in a small-business wireless network?
A. automatically configures wireless client devices via Wi-Fi Protected Setup
B. can get real-time traffic or bandwidth statistics form an access point within a cluster
C. replicates configuration parameters across access points in the cluster, while optimizing network performance
D. allows multiple access points to be connected wirelessly, without the need for a wired Ethernet network

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 54
What are two uses for USB ports on ISRs? (Choose two)
A. increased memory capabilities
B. secure device authentication
C. bulk flash storage
D. control over the types of files that can be stored
E. digital certificate storage

Correct Answer: BC Section: (none) Explanation
Explanation/Reference:
QUESTION 55
When troubleshooting poor network performance, which two symptoms would typically be associated with a network layer problem? (Choose two)
A. Packet loss is more than 30 percent
B. There is excessive broadcast traffic
C. There are excessive CRC errors
D. Pings succeed only part of the time
E. Slips are detected on WAN interfaces
F. ARP requests are timing out

Correct Answer: AD Section: (none) Explanation
Explanation/Reference: QUESTION 56
Which screen on the Cisco ASDM home page would you use to see which access list rules are in effect?
A. NAT
B. Interfaces
C. Routing
D. Security Policy

Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 57
Which type of antenna is used when coverage in all directions is required?
A. directional
B. bidirectional
C. omnidirectional
D. patch

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 58
Which service should be disabled or filtered via a firewall because an attacker could use the service to download a copy of Cisco IOS software from a router (thereby making the router vulnerable to DOC attacks)?
A. PAD service
B. finger service
C. TCP/UDP
D. BOOTP

Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 59
Which two statement best describe the wireless core feature set using autonomous access points when implementing Wireless Domain Services? (Choose two)
A. Layer 2 and Layer 3 services can be configured in a CiscoAironet autonomous AP or a Cisco Integrated Services Router
B. Layer 2 services can be configured in a CiscoAironet autonomous AP or a Cisco Integrated Services Router
C. Layer 2 and Layer 3 services can be configured in a CiscoAironet autonomous AP or controllers
D. Layer 3 services can be configured in WLSM
E. Layer 3 services can be configured in WLSE

Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 60
Refer to the exhibit.

Switches A and C are running PVST+ STP, and switch B is running 802.1Q STP, if the BPDU of the root in VLAN 1 is better than the BPDU of the root in VLAN 2, then there is no blocking port in the VLAN 2 topology. The BPDU of VLAN 2 never makes a full circle around the topology, it is replaced by the VLAN 1 BPDU on the B_C link, because B runs only one STP merged with VLAN ! STP of PVST+ Thus, there is a forwarding loop What does PVST+ do to correct this?
A. Switch A sends PVST+BPDUs of VLAN 2 (to the SSTP address that is flooded by switch B) towards Switch C. Switch C will put port C-B into a type-inconsistent, which prevents the loop
B. Switch B sends PVST+BPDUs of VLAN 1 (to the SSTP address that is flooded by switch A) towards Switch C. Switch C will put port C-B into a type-inconsistent, which prevents the loop
C. Switch C sends PVST+BPDUs of VLAN 2 (to the SSTP address that is flooded by switch B) towards Switch C. Switch C will put port C-B into a type-inconsistent, which prevents the loop
D. Switch A sends PVST+BPDUs of VLAN 1 (to the SSTP address that is flooded by switch B) towards Switch B. Switch A will put port C-B into a type-inconsistent, which prevents the loop “Pass Any Exam. Any Time.” – www.actualtests.com 21 Cisco 642-384: Practice Exam

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 61
What is used to prevent outside resources from accessing private information within the company?
A. IPsec
B. VPN
C. PIN
D. Firewalls

Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 62
Which type of security allows visibility into the state of the operating system and is the only way to inspect encrypted traffic?
A. zero updated architecture
B. network-based security
C. endpoint-based security
D. ACLs

Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 63
Which two benefits will a client see from adding a Wireless LAN Controller to their Smart Business Communications System? (Choose two)
A. allow for guest access
B. increase connection speeds
C. add additional access points
D. network management with CLI

Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 64
To avoid carrying every length of cable, lighting arrestors, and splitters when performing site surveys, engineers can outfit their survey kits with which item?
A. Category 5 cable
B. RP-TNC plug
C. antenna attenuator D. RP-TNC connector

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 65
Which two are components of AAA? (Choose two)
A. access control lists
B. Cisco IOS Software
C. Cisco Secure Access Control Server
D. Security Audit wizard
E. network access server

Correct Answer: CE Section: (none) Explanation
Explanation/Reference:
QUESTION 66
Which three business requirements development activities are performed in the prepare phase before creating a technology strategy? (Choose three)
A. identifying and assessing customer business requirements
B. documenting and categorizing customer business requirements in terms of performance, availability, capacity, and security
C. producing a documented technology strategy
D. creating a bill of materials
E. presenting documented business requirements to a customer and having the customer validate them
F. completing a site survey

Correct Answer: ABE Section: (none) Explanation
Explanation/Reference:
QUESTION 67
Which port-sales SMART Design documents are available to help you better serve your customers? (Choose three)
A. Design Guide
B. Small Business Product Guide
C. Implementation Guide
D. Solution Profile
E. Cisco Configuration Assistant
F. Application Notes

Correct Answer: ACF Section: (none) Explanation Explanation/Reference:
QUESTION 68
Which type of VPN is deal for employees who use a home PC or public computer to access the network?
A. IP secemote access VPN
B. mobile VPN
C. dialup 0ffload VPN
D. SSL VPN
E. GET VPN

Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 69
Which benefit can be obtained by using the change management service component in the operate phase?
A. reduced operating costs, due to consistent framework for making necessary changes in an efficient and accountable manner
B. greater accuracy, completeness, and timeliness of network configuration information
C. notification provided to interested parties regarding problems that have been identified, and a system that scales with customer requirements
D. improved system service quality and fewer disruptions

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 70
Refer to the exhibit.

The tables contain information from the Cisco Configuration Professional configurations of Router A and
Router B. Traffic between Host 1 and Host 2 is not successfully establishing the site-to-site VPN between
Router A and Router B.
What is the mostly likely cause of this fault?

A. Router A is using a standard IP ACL (100-149) while Router B is using a Turbo ACL (150199)
B. The IKE encryption methods on the two routers are different
C. The IPSec policy map names on the two routers are different
D. The IPSec rules on the two routers are not permitting the correct interesting traffic

Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 71
Which of the following best describe the customer benefits of change management in the operate phase?
A. reduce unnecessary disruption, delays, rework, and other problems by establishing test cases for use in verifying that the system meets operational, functional, and interface requirements
B. improve its ability to make sound financial decisions by developing a business case based on its business requirements and establishing a basis for developing a technology strategy
C. reduce operating costs and limit changE.related incidents by providing a consistent and efficient set of processes
D. improve the return on investment and hasten migration by identifying and planning for necessary infrastructure changes and resource additions, as well as reduce deployment costs by analyzing gaps early in the planning process to determine what is needed to support the system

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 72
Which of these is the best definition of the Cisco Lifecycle Services approach?
A. It defines the minimum set of services required to successfully deploy and operate a set of Cisco technologies.
B. It determines how best to price Cisco products.
C. It provides partners with a useful way to leverage Cisco resources.
D. It consists of these phases: plan, deploy, support, and troubleshoot.

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 73
What two types of telephony interfaces are used for PSTN connectivity? (Choose two.)
A. Digital
B. Optical
C. Analog
D. CDMA

Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 74
Which statement correctly describes the keys witch model of deployment for call processing?
A. All IP Phones are able to answer any incoming PSTN call on any line
B. PSTN calls are routed through a receptionist or automated attendant.
C. All IP Phones in the system have a single unique extension number.

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 75
Which definition best describes the implementation service component within the implement phase?
A. providing a step-by-step plan that details the installation andservicE.commission tasks required in order to create a controlleD.implementation environment that emulates a customer network
B. assessing the ability of site facilities to accommodate proposed infrastructure changes
C. developing and executingprooF-oF-concept tests, validating high-level infrastructure design, and identifying any design enhancements
D. Installing, configuring and integrating systems components based on an implementation plan developed in earlier phases
E. improving a customer’s infrastructure security system

Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 76
A customer with a small enterprise network of 15 remote sites is trying to optimize its VPN by migrating some remote sites using Frame Relay connections to the Internet to using cable connections to the Internet. Minimizing costs is one of the customer’s highest priorities. Only a moderate amount of IP traffic is passing through the network, most of which is from the remote sites to the central site. IPSec should be used to provide VPN functionality and basic confidentiality is desired.
Based on the traffic patterns, which topology would be the easiest for this customer to set up and manage?
A. full mesh
B. partial mesh
C. point-to-multipoint
D. hub and spoke

Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 77
How can the proper configuration of Voice Mail be tested at an end user’s IP phone?
A. Press the “i” button.
B. Press the “Settings” button.
C. Press the “Services” button.
D. Press the “Messages” button

Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 78
In what location is it recommended that the Cisco Catalyst 6500 Series WLSM be placed?
A. distribution layer
B. core layer
C. access layer
D. network management functional module
Correct Answer: A Section: (none) Explanation

Explanation/Reference:
QUESTION 79
Which of these is an accurate list of Cisco Lifecycle Services phases?
A. initiation, planning, analysis, design, development, implementation, operations and maintenance
B. project planning, site assessment, risk assessment, solution selection and acquisition, testing, and operations
C. Prepare, plan design implement operate, and optimize
D. analysis, design, deployment, testing, implementation, and production I E. presales, project planning, development, implementation, operations testing, and operations sign-off

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 80
What port role assignment would you make for the Gigabit Ethernet port on the Cisco CE520 used in the Smart Business Communications System?
A. IP Phone and desktop
B. Cisco UC520
C. Cisco CE520
D. Cisco 871W

Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 81
This item consists of one or more multiple choice type questions that you must answer. To answer these questions, you need to use a GUI tool that becomes fully accessible by the use of the labs you see below these directions. The tabs have up and down arrows to signal the direction that the tabbed window may be dragged lo expose or hide the GUI tool. When you are done using the GUI tool, you may drag the tab down to continue answering questions. To advance to the next question in the series, click on the numbered button to the left of each question. Make sure that you have answered all the questions before continuing to the next item.

Which method list and method is used to authenticate the remote access VPN users? (Choose two.)
A. sdm_vpn_xauth_ml_1
B. sdm_ypn_group_ml_1
C. SDM_CMAP_1
D. local database on the ISR
E. remote TACACS+ server
F. remote Radius Server

Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 82
Refer to the exhibit. Switches A and C are running PVST+ STP, and Switch B is running 802.10 STP. If the
BPDU of the root in VLAN 1 is better than the BPDU of the root in VLAN 2, then there is no blocking port in
the VLAN topology. The BPDU of VLAN 2 never makes a “full circle” around the topology; it is replaced by
the VLAN 1 BPDU on the B. C link, because B runs only one STP merged with VLAN 1 STP of PVST+.
Thus, there is a forwardin loop.
What does PVST+ do to correct this?
A. Switch A sends PVST+ BPDUs of VLAN 2 (to the SSTP address that is flooded by Switch B) towards Switch C. Switch C will put port C.B into a typE.inconsistent state, which prevents the loop.
B. Switch B sends PVST+ BPDUs of VLAN 1 (to the SSTP address that is flooded by Switch A) towards Switch C. Switch C will put port C.B into a typE.inconsistent state, which prevents the loop.
C. Switch C sends PVST+ BPDUs of VLAN 2 (to the SSTP address that is flooded by Switch B) towards Switch C. Switch A will put port C.B into a typE.inconsistent state, which prevents the loop.
D. Switch A sends PVST+ BPDUs of VLAN 1 (to the SSTP address that is flooded by Switch B) towards Switch B. Switch A will put port C.B into a typE.inconsistent state, which prevents the loop. Switch B sends PVST+ BPDUs of VLAN 1 (to the SSTP address that is flooded by Switch A) towards Switch C. Switch C will put port C.B into a typE.inconsistent state, which prevents the loop.
E. Switch C sends PVST+ BPDUs of VLAN 2 (to the SSTP address that is flooded by Switch B) towards Switch C. Switch A will put port C.B into a typE.inconsistent state, which prevents the loop.
F. Switch A sends PVST+ BPDUs of VLAN 1 (to the SSTP address that is flooded by Switch B) towards Switch B. Switch A will put port C.B into a typE.inconsistent state, which prevents the loop.

Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 83
Which interface on the Cisco UC520 is assigned an IP address either statically or through DHCP?
A. Switch B sends PVST+ BPDUs of VLAN 1 (to the SSTP address that is flooded by Switch A) towards Switch C. Switch C will put port C.B into a typE.inconsistent state, which prevents the loop.
B. Switch C sends PVST+ BPDUs of VLAN 2 (to the SSTP address that is flooded by Switch B) towards Switch C. Switch A will put port C.B into a typE.inconsistent state, which prevents the loop.
C. Switch A sends PVST+ BPDUs of VLAN 1 (to the SSTP address that is flooded by Switch B) towards Switch B. Switch A will put port C.B into a typE.inconsistent state, which prevents the loop. Switch B sends PVST+ BPDUs of VLAN 1 (to the SSTP address that is flooded by Switch A) towards Switch C. Switch C will put port C.B into a typE.inconsistent state, which prevents the loop.
D. Switch C sends PVST+ BPDUs of VLAN 2 (to the SSTP address that is flooded by Switch B) towards Switch C. Switch A will put port C.B into a typE.inconsistent state, which prevents the loop.
E. Switch A sends PVST+ BPDUs of VLAN 1 (to the SSTP address that is flooded by Switch B) towards Switch B. Switch A will put port C.B into a typE.inconsistent state, which prevents the loop.
F. WAN interface
G. LAN interface
H. Switch port
I. PSTN Interface

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 84
Which benefit can be obtained by using the change management service component in the operate phase?
A. Reduced operating costs due to a consistent framework for making necessary changes in an efficient and accountable manner
B. Greater accuracy, completeness, and timeliness of network configuration information
C. Notification provided to interested parties regarding problems that have been identified, and a system that scales with customer requirements
D. Improved system service quality and fewer disruptions

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 85
What are two ways to test the LAN connectivity on the Cisco CE520? (Choose two.)
A. Ping the IP address of the Cisco-Data Access VLAN from the Cisco UC520 console.
B. Ping the IP address of the Cisco-Data VLAN from a device attached to the Cisco CE520
C. Ping default gateway from the Cisco UC520.
D. Ping the IP address of the Cisco-voice VLAN from a device attached to the Cisco CE520.
E. Ping default gateway from the Cisco CE520.
F. Ping the IP address of the Cisco-Distribution VLAN from the Cisco UC520 console.

Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 86
Which statement correctly describes configuration of the VPN server?
A. It requires definition of a Group ID for remote clients.
B. It requires configuration of port settings for the VPN server on the Cisco UC520.
C. It uses apreshared Key for remote device authentication
D. The WAN interface is preselected.

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 87
In a new Cisco UC520 installation, when must IP routing be configured?
A. When the service provider assigns static IP information
B. When the service provider assigns dynamic IP information.
C. When analog PSTN trunks are used.
D. When digital PSTN trunks are used.

Correct Answer: A Section: (none) Explanation
Explanation/Reference: