Buy Latest New Version Professional Cisco 640-816 With All New Answers and Questions For Groundbreaking Results 100% Valid

Ensure that you are provided with only the best and most updated Cisco 640-816 Certification training materials, we also want you to be able to access Cisco 640-816 easily, whenever you want.We provide all our Cisco 640-816 Certification exam training material in PDF format, which is a very common format found in all computers and gadgets. Now we add the latest Cisco 640-816 content and to print and share content.

Exam A QUESTION 1
Then click My Account
A.
B.
C.
D.

Correct Answer: QUESTION 2
Refer to the exhibit.
A junior network engineer has prepared the exhibited configuration file. What two statements are true of the planned configuration for interface fa0/1? (Choose two.)
A. The two FastEthernet interfaces will require NAT configured on two outside serial interfaces.
B. Address translation on fa0/1 is not required for DMZ Devices to access the Internet.
C. The fa0/1 IP address overlaps with the space used by s0/0.
D. The fa0/1 IP address is invalid for the IP subnet on which it resides.
E. Internet hosts may not initiate connections to DMZ Devices through the configuration that is shown.
Correct Answer: BE
QUESTION 3
Refer to the exhibit. Which statement describes DLCI 17?

A. DLCI 17 describes the ISDN circuit between R2 and R3.
B. DLCI 17 describes a PVC on R2. It cannot be used on R3 or R1.
C. DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.
D. DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider.
Correct Answer: C QUESTION 4

What is the default Local Management Interface frame type transmitted by a Cisco router on a Frame Relay circuit?
A. Q933a
B. B8ZS
C. IETF
D. Cisco

E. ANSI
Correct Answer: D QUESTION 5
Refer to the exhibit. The network shown in the exhibit has just been installed. Host B can access the Internet, but it is unable to ping host C. What is the problem with this configuration?
A. Host B should be in VLAN 13.
B. The address of host C is incorrect.
C. The gateway for host B is in a different subnet than the host is on.
D. The switch port that sends VLAN 13 frames from the switch to the router is shut down.
E. The switch port connected to the router is incorrectly configured as an access port.

Correct Answer: B QUESTION 6
Refer to the exhibit. The router has been configured with these commands: hostname Gateway interface FastEthernet 0/0 ip address 198.133.219.14 255.255.255.248 no shutdown interface FastEthernet 0/1 ip address 192.168.10.254 255.255.255.0 no shutdown interface Serial 0/0 ip address 64.100.0.2 255.255.255.252 no shutdown ip route 0.0.0.0 0.0.0.0 64.100.0.1 What are the two results of this configuration? (Choose two.)
A. The default route should have a next hop address of 64.100.0.3.
B. Hosts on the LAN that is connected to FastEthernet 0/1 are using public IP addressing.
C. The address of the subnet segment with the WWW server will support seven more servers.
D. The addressing scheme allows users on the Internet to access the WWW server.
E. Hosts on the LAN that is connected to FastEthernet 0/1 will not be able to access the Internet without address translation.
Correct Answer: DE

Cisco 640-816 tests containing questions that cover all sides of tested subjects that help our members to be prepared and keep high level of professionalism. The main purpose of Cisco 640-811 exam is to provide high quality test that can secure and verify knowledge, give overview of question types and complexity that can be represented on real exam certification
QUESTION 7
Refer to the exhibit. Two routers have just been configured by a new technician. All interfaces are up.
However, the routers are not sharing their routing tables. What is the problem?

A. Split horizon is preventing Router2 from receiving routing information from Router1.
B. Router1 is configured for RIP version 2, and Router2 is configured for RIP version 1.
C. Router1 has an ACL that is blocking RIP version 2.
D. There is a physical connectivity problem between Router1 and Router2.
E. Router1 is using authentication and Router2 is not.
Correct Answer: B
QUESTION 8
Refer to the exhibit. What can be concluded from the output of the debug command?
A. The output represents normal OSPF operation.
B. The interfaces of two OSPF routers connected to the Border router are in the same subnet.
C. The OSPF router connected to interface Serial0/1 has NOT formed a neighbor relationship with the Border router.
D. A router is connected to interface Serial0/3 of the Border router. The OSPF router ID of the connected router is the IP address of the connected interface.

Correct Answer: C QUESTION 9
Refer to the output from the show running-config command in the exhibit. What should the administrator do to allow the workstations connected to the FastEthernet 0/0 interface to obtain an IP address?
A. Apply access-group 14 to interface FastEthernet 0/0.
B. Add access-list 14 permit any any to the access list configuration.
C. Configure the IP address of the FastEtherent 0/0 interface to 10.90.201.1.
D. Add an interface description to the FastEthernet 0/0 interface configuration.

Correct Answer: C QUESTION 10
S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally, static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIP v2 in place of the static routes?

A. Configure the no ip subnet-zero command on R1, R2, and R3.
B. Dynamic routing protocols such as RIP v2 cannot be used across Frame Relay networks.
C. Configure the s0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.
D. Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.
E. Change the network address configurations to eliminate the discontiguous 172.16.2.0/25 and

Correct Answer: QUESTION 11
16.2.128/25 subnetworks.
A.
B.
C.
D.

Correct Answer: QUESTION 12
Refer to the exhibit. HostA cannot ping HostB. Assuming routing is properly configured, what could be the cause of this problem?

A. HostA is not on the same subnet as its default gateway.
B. The address of SwitchA is a subnet address.
C. The Fa0/0 interface on RouterA is on a subnet that can’t be used.
D. The serial interfaces of the routers are not on the same subnet.
E. The Fa0/0 interface on RouterB is using a broadcast address.

Correct Answer: D

Get certified Cisco 640-816 is a guaranteed way to succeed with IT careers. We help you do exactly that with our high quality ISC Cisco 640-816 Certification Certified Information Systems Security Professional training materials.